Exactly how to Replace a Bath Tub ( Guide).
Exactly how to Replace a Bath Tub ( Guide).
Blog Article
Just how do you actually feel when it comes to How to Install a Bathtub Yourself?
Mounting a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall surface to remove the old tub and also position the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have actually qualified on your own for the work and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This write-up will help you set up a new tub in your washroom if you have actually already acquired a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product list must consist of the following:
Preparing for the Setup
To start with, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome due to the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, position the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews degree.
To install faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water system as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Load the bathtub and additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has actually been made use of at least once as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, leading to difficulties with wetness and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I am very fascinated by A Step-by-Step Guide to Installing a Bathtub and I am hoping you enjoyed my piece. Those who appreciated our blog post please be sure to pass it around. Thanks for going through it.
Get An Estimate Report this page